葡京APP下载中心_葡萄京娱乐场网上平台网站

葡京APP下载中心
热线电话:400-879-1999 山汽官方微信
郑重声明 购机 售后
在线询价
热线电话:400-879-1999
您现在所在的位置: 首页> 新闻资讯 > 行业新闻 >

搅拌车的罐体故障如何维修?

所属分类:行业新闻 发布时间:2020-07-13 来源: 浏览量:18

  全自动上料搅拌车用溶剂彻底清理阀杆和阀体。用压缩空气吹干所有零件,然后用ATF油作为润滑剂,重新组装。大家在选择时我们会有专门的技术人员为大家解答,建议大家收工时,要彻底清洗混凝土贮罐及进出料口周围,保证不粘有水泥及混凝土结块。在阀杆表面涂ATF油,然后将其落入阀孔中。阀杆应能靠自重落入阀孔底部。否则,重复步骤,重新测试。如果阀杆仍然卡滞,则更换阀体。
  Clean the valve stem and valve body thoroughly with solvent. Dry all parts with compressed air and reassemble with ATF oil as lubricant. When you choose, we will have a special technical personnel to answer for you. It is suggested that when you finish work, you should thoroughly clean the concrete storage tank and the area around the inlet and outlet to ensure that there is no cement and concrete caking. Coat the surface of the valve stem with ATF oil and drop it into the valve hole. The valve stem should be able to fall into the bottom of the valve hole by its own weight. Otherwise, repeat step and retest. If the stem is still stuck, replace the valve body.
  全自动上料搅拌车的检修在整个工程作业中也是极为重要的,做好基本的检修我们的工作才能正常进行。首先将砂纸置于ATF油中,浸泡约30分钟。小心地敲击阀体,使卡滞的阀杆从阀腔孔中落下。可能有必要使用一把小螺丝刀,将其撬出。
          全自动上料搅拌车
  The maintenance of the automatic feeding mixer is also very important in the whole project operation. Only by doing a good job in the basic maintenance can our work be carried out normally. First place sandpaper in ATF oil and soak for about 30 minutes. Carefully tap the valve body to allow the stuck stem to fall out of the cavity bore. It may be necessary to lever it out using a small screwdriver.
  全自动上料搅拌车小心不要划伤阀孔。单向阀杆是否有摩擦痕迹。使用ATF油浸泡过的#600砂纸,打磨阀杆上的毛刺,然后在溶剂中清洗阀杆并用压缩空气吹干。卷起半张ATF油浸泡过的#600砂纸,将其插入卡滞阀杆的阀孔中。轻轻扭动砂纸,使砂纸松卷,紧密贴合在阀孔表面,然后边推拉,边扭卷砂纸,打磨阀孔。抽出#600砂纸。在溶剂中彻底清洗整个阀体,然后用压缩空气吹干。
  Be careful not to scratch the valve hole on the automatic feeding mixer. Check whether there are friction marks on the one-way valve stem. Grind the burrs on the valve stem with ? 600 sandpaper soaked in ATF oil, then clean the valve stem in solvent and dry it with compressed air. Roll up half a piece of ? 600 sandpaper soaked in ATF oil and insert it into the valve hole with stuck valve stem. Gently twist the sandpaper to make the sandpaper loose and tightly fit on the surface of the valve hole. Then, while pushing and pulling, twist the sandpaper to polish the valve hole. Draw out 600 sandpaper. Clean the entire valve body thoroughly in solvent and blow dry with compressed air.
  以上是关于搅拌车罐体故障维修的措施,想要了解更多搅拌机内容欢迎点击官网给我们留言。
  The above is about the mixer tank troubleshooting measures, want to learn more about mixer content, welcome to click Leave us a message on the official website.
热门产品 / HOT PRODUCT

 

首页 产品 电话 置顶
Baidu
sogou